This high-performance drive solution features a compact 24.4mm diameter design with an integrated driver for seamless control. As a HBL2430 Micro Brushless DC Gear Motor, it delivers efficient power output up to 3.7W and speeds up to 7100 RPM. This 24V Micro Brushless DC Motor ensures stable, low-noise operation for precision equipment.
Dimension
| MODEL (型号) |
VOLTAGE 电压 | NOLOAD无负荷 | AT MAXIMUM EFFICIENCY最大效率点 | STALL起劲 | ||||||||
|
OPERATIN GRANGE |
NOMINAL | SPEED | CURRENT | SPEED | CURRENT | TORQUE | OUTPUT | TORQUE | CURRENT | |||
| r/min | A | r/min | A | mN.m | g.cm | w | mN.m | g.cm | A | |||
| PC-BL-2430WH-01 | 5.0-12.0 | 9.0V | 5400 | 0.110 | 4268 | 0.402 | 4.86 | 49.6 | 2.168 | 23.14 | 236.0 | 1.50 |
| PC-BL-2430WH-02 | 8.0-26.0 | 12.0V | 7100 | 0.120 | 5600 | 0.446 | 6.34 | 64.7 | 3.721 | 30.2 | 308.0 | 1.67 |
Why Choose BL2430 Brushless Gear Motor?
- Space-Saving Design: Featuring a 24.4mm miniature diameter, perfect for handheld devices and narrow installation environments.
- Plug-and-Play Integration: The internal driver eliminates the need for external speed controllers, simplifying your system's PCB footprint.
- High Control Resolution: 5-wire interface (PWM/FG/DIR) allows for delicate speed modulation and real-time RPM monitoring for closed-loop tasks.
- Low Power Consumption: Rated at approximately 1.0-8.0W, ensuring long battery life in portable medical or personal care gadgets.
[PDF] Download 2430WH Data Sheet
Application Scenarios
| Target Industry | Specific Scenario |
Value Proposition |
| Medical Devices | Peristaltic & dosing pumps |
Precise flow control in compact kits. |
| Personal Care | Facial cleansers & massagers |
Lightweight & high power density. |
| Smart Security | Smart locks & PTZ cameras |
Quiet operation & high startup torque. |
| Laboratory | Stirrers & diagnostic equipment |
Stable performance across 5-26V range. |
Wiring Definition Table
| Wire Color | Signal Label | Functional Description |
Integration Benefit |
| Red | VCC | Power Positive (9V/12V Nominal) |
Wide 5V-26V operating range for flexible power sourcing. |
| Green | FG | Frequency Generation (Speed Feedback) |
Provides 6 pulses/rev for precise real-time RPM monitoring. |
| Yellow | CW/CCW | Direction Control |
Simple logic-level switching; no H-bridge circuit required. |
| Black | GND | Common Ground |
Centralized grounding for stable signal logic. |
| Blue | PWM | Pulse Width Modulation (Speed Input) |
Direct MCU speed control via 10kHz-30kHz signal. |
- Internal Rotor Excellence: Unlike larger motors, the BL-2430CH uses an inner rotor architecture to achieve rapid acceleration and high responsiveness.
- Predictable Performance: Our T-N-I curve data confirms linear torque output (up to 30.2 mN.m stall torque), allowing for predictable system behavior under varying loads.
- Safety Protection: Equipped with built-in current limiting and stall protection (Stall Current: 1.5A - 1.67A) to safeguard your device's electronics.
FAQ
Q1: Does this motor require an external driver?
A: No. Unlike the high-power 4260WH, the BL-2430CH features an integrated internal driver. Its 5-wire interface connects directly to your MCU, saving significant PCB space.
Q2: Is it suitable for battery-powered devices?
A: Yes. This motor operates efficiently between 1.0W and 8.0W. With a low no-load current of only 0.11A–0.12A, it offers much longer battery life for portable instruments compared to 50W models.
Q3: Will the motor burn out if it stalls?
A: It includes built-in protection. According to the datasheet, the stall current is limited to 1.50A–1.67A, preventing the coils from overheating during unexpected mechanical failures.
Certification
Our factory
